Mass Transfer and Diffusion & Membrane Processing Quiz
GIFSQ ID: ART-0952
What this quiz covers
Mass transfer is the quiet physics behind drying, membrane separation, and flavour loss, and this quiz tests it as a table of numbers. You will meet diffusion coefficients for gases in air, osmotic pressures for milk, whey, juices, and coffee extract, vapour diffusivities at 0 degrees C, aqueous diffusion at 25 degrees C, and the feed channel diameters of the four membrane module types.
Twenty questions cover sulphur dioxide at 10.3, sulphur trioxide at 9.4, and water vapour at 21.9, all times 10 to the minus 6 square metres per second; milk and whey both near 690 kPa, orange juice at 1587, apple and grape juice at 2070, and coffee extract at 3450; a 5 percent lactose solution at 380 kPa and a 1 percent salt solution at 862 kPa; acetic acid vapour at 1.33, ethyl acetate at 0.71, and n-butyl alcohol at 0.70, all times 10 to the minus 5 square metres per second; oxygen diffusing fastest and catalase slowest in water; and feed channels of 5 mm for plate-and-frame, 1.3 mm for spiral-wound, 13 mm for tube-in-shell, and 0.1 mm for hollow-fibre modules.
Concepts you will need
Two rules carry the numbers. First, diffusion follows molecular weight: lighter molecules move faster, which is why water vapour beats sulphur dioxide and oxygen beats glucose in water. Second, osmotic pressure follows dissolved solids: more dissolved sugar or salt means higher pressure, which is why coffee extract at 28 percent solids sits far above milk. Learn the rules and the tables read as rankings, not as loose figures.
How to use this quiz
You get 20 seconds per question and one attempt at each answer, so rank before you pick a number. For a diffusion question, ask which molecule is lightest: the lightest is fastest. For an osmotic pressure question, ask which liquid carries the most dissolved solids: the most concentrated is highest. Then retake the quiz and check the rankings hold.
Choose how you want to play
Answer explanations
Worked through the quiz? Here is why each correct answer is correct: the concept behind it, in plain terms.
- What is the diffusion coefficient (× 10⁻⁶ m²/s) of sulphur dioxide in air under standard conditions?
Correct answer: 10.3. Sulphur dioxide diffuses through air at about 10.3 times 10 to the minus 6 square metres per second under standard conditions. Kinetic theory says heavier gases diffuse more slowly, and SO2 at molar mass 64 is heavier than water vapour, so its coefficient sits below water's 21.9. - What is the diffusion coefficient (× 10⁻⁶ m²/s) of sulphur trioxide in air under standard conditions?
Correct answer: 9.4. Sulphur trioxide is the heaviest of the three gases here at molar mass 80, so it diffuses slowest, about 9.4 times 10 to the minus 6 square metres per second. The ranking SO3 below SO2 below water vapour follows molecular weight exactly, as Graham's law predicts. - What is the diffusion coefficient (× 10⁻⁶ m²/s) of water vapour in air under standard conditions?
Correct answer: 21.9. Water vapour diffuses through air at about 21.9 times 10 to the minus 6 square metres per second: the fastest of the three because it is the lightest, at molar mass 18. The tabulated 0.219 square cm per second at 0 degrees C and 1 atm converts directly to 21.9. - What is the osmotic pressure (kPa) of milk (9% SNF)?
Correct answer: 690. Milk at 9 percent solids-not-fat has an osmotic pressure near 690 kPa. Osmotic pressure tracks dissolved species, lactose and mineral salts, not fat or protein, and milk carries enough of both to sit near 0.7 MPa. - What is the osmotic pressure (kPa) of whey (6% TS)?
Correct answer: 690. Whey at 6 percent total solids matches milk at 690 kPa because it keeps the osmotically active fraction. Removing fat and casein drops total solids but leaves lactose and salts, the species that actually drive osmotic pressure, so the value barely moves. - What is the osmotic pressure (kPa) of orange juice (11% TS)?
Correct answer: 1587. Orange juice at 11 percent total solids has an osmotic pressure near 1587 kPa. Sugars are the dominant dissolved species in juice, and at 11 percent solids their concentration pushes osmotic pressure well above milk. - What is the osmotic pressure (kPa) of apple juice (15% TS)?
Correct answer: 2070. Apple juice at 15 percent total solids sits near 2070 kPa. More dissolved sugar than orange juice means proportionally higher osmotic pressure: the van't Hoff relationship runs roughly linear in solute concentration. - What is the osmotic pressure (kPa) of grape juice (16% TS)?
Correct answer: 2070. Grape juice at 16 percent total solids is tabulated at 2070 kPa, essentially the same as apple juice. The two juices carry similar dissolved-sugar loads at these solids levels, so their osmotic pressures coincide. - What is the osmotic pressure (kPa) of coffee extract (28% TS)?
Correct answer: 3450. Coffee extract at 28 percent total solids reaches about 3450 kPa, the highest in the series. Osmotic pressure climbs with dissolved-solids concentration, and 28 percent solids is nearly double the juices. - What is the osmotic pressure (kPa) of a 5% w/v lactose solution?
Correct answer: 380. A 5 percent w/v lactose solution has an osmotic pressure near 380 kPa. A quick van't Hoff check confirms it: 50 g per litre divided by 342 g per mol gives about 0.146 mol per litre, and pi equals CRT lands near 360 to 380 kPa at room temperature. - What is the osmotic pressure (kPa) of a 1% w/v sodium chloride solution?
Correct answer: 862. A 1 percent w/v sodium chloride solution sits near 862 kPa. Salt dissociates into two ions, so its van't Hoff factor is about 2: 10 g per litre divided by 58.44 g per mol, times 2, times RT, lands near 850 kPa. The tabulated 862 kPa reflects that doubling effect. - At 0 °C and atmospheric pressure, how quickly does acetic acid vapour diffuse through air, in 10⁻⁵ m²/s?
Correct answer: 1.33. Acetic acid vapour diffuses through air at about 1.33 times 10 to the minus 5 square metres per second at 0 degrees C and atmospheric pressure. It is the lightest of the three vapours here, so kinetic theory puts it fastest. - At 0 °C and atmospheric pressure, what is the diffusivity of ethyl acetate vapour in air, in 10⁻⁵ m²/s?
Correct answer: 0.71. Ethyl acetate vapour moves through air at about 0.71 times 10 to the minus 5 square metres per second at 0 degrees C and 1 atm. Heavier than acetic acid, it diffuses more slowly: the Graham's-law ordering holds across the whole series. - n-Butyl alcohol vapour drifts through air at 0 °C and atmospheric pressure. What is its diffusivity in 10⁻⁵ m²/s?
Correct answer: 0.70. n-Butyl alcohol vapour diffuses at about 0.70 times 10 to the minus 5 square metres per second, the slowest of the three vapours. As the heaviest molecule in the set, it has the lowest molecular speed at a given temperature. - In dilute aqueous solution at 25 °C, which substance diffuses fastest?
Correct answer: Oxygen. Oxygen diffuses fastest in dilute aqueous solution at 25 degrees C, at about 2.10 times 10 to the minus 9 square metres per second. Small dissolved gases outrun larger molecules: oxygen edges out carbon dioxide at 1.92 and dwarfs glucose at 0.69. Molecular size dominates the ranking. - In dilute aqueous solution at 25 °C, which substance diffuses slowest?
Correct answer: Catalase. Catalase diffuses slowest: it is a protein of roughly 240 kDa, enormous beside lactose, urea, or ethanol. Diffusivity falls as molecular size rises, so the macromolecule trails at about 0.04 times 10 to the minus 9 square metres per second. Size is the whole story here. - What is the feed channel diameter (mm) of a plate-and-frame module?
Correct answer: 5. Plate-and-frame modules use feed channels around 5 mm. The flat-sheet stack leaves relatively wide gaps between plates, which suits viscous or fouling-prone feeds. Wider channels are the price of that fouling tolerance. - What is the feed channel diameter (mm) of a spiral-wound module?
Correct answer: 1.3. Spiral-wound modules run feed channels near 1.3 mm, the thickness of the feed-spacer mesh. That narrow gap packs far more membrane area into each housing than plate-and-frame, at the cost of fouling sensitivity. - What is the feed channel diameter (mm) of a tube-in-shell module?
Correct answer: 13. Tube-in-shell, tubular, modules have the widest channels here, about 13 mm. The large tube diameter handles high-solids and viscous feeds with the lowest fouling risk of any configuration. Diameter is this module's defining advantage. - What is the feed channel diameter (mm) of a hollow-fibre module?
Correct answer: 0.1. Hollow-fibre modules use the narrowest channels, about 0.1 mm inside the fibres. Thousands of fine fibres bundle into each housing, which is how the configuration reaches packing densities of 9000 to 30000 square metres per cubic metre. Tiny diameter is what buys that density.