Login Register

Access the GIFSQ Portal

Select your user type to log in or register a new account.

Student Portal

Access your food safety courses and exams.

Instructor Portal

Manage courses, view student submissions, and grade quizzes.

Company Portal

Manage corporate setup, view employee logs, and access QA services.

Resources  /  Knowledge Base  /  Food Analysis  /  Current Article

Difference Between Ash Content and Mineral Content

GIFSQ ID: KBA-0282

FOOD ANALYSIS : MINERALS AND ASH

From a food to its ash, then from the ash to single minerals

Weigh the sample in a dish
↓
Char gently so it does not spit
↓
Burn in the furnace near 550 °C until the ash is pale
↓
Cool in a desiccator, weigh: that is the ash content
↓
Dissolve the ash and test single minerals: flame photometry for sodium and potassium, atomic absorption for calcium, iron, and zinc

Figure 1: Ash content is the first step. Mineral content is the second step, taken from the dissolved ash.

Introduction

Ash content and mineral content are often mixed up, but one is the total and the other is the detail. Ash content is the inorganic residue left after a food is burned completely in a furnace, usually at about 550 °C: the organic parts burn away as CO₂, H₂O, and N₂, and what remains is the mineral part as oxides and salts, reported as a percentage of the sample weight. Mineral content is the amount of single minerals, such as calcium, potassium, sodium, magnesium, iron, and phosphorus, measured one by one from the dissolved ash.

Quick comparison

Table 1: Ash content compared with mineral content

AspectAsh contentMineral content
What it meansTotal mineral matter in the food, as one numberSingle minerals, each measured on its own
How it is foundBurn the sample in a muffle furnace and weigh the residueDissolve the ash and measure each element by flame photometry or atomic absorption
UnitPercent of the sample weightMilligrams per 100 g, or parts per million, for each element
Tells youHow much mineral matter there is in totalWhich minerals are present and how much of each
ApparatusMuffle furnace, dish, desiccator, balanceFlame photometer for sodium and potassium, atomic absorption spectrometer for calcium, iron, and zinc
TemperatureUsually about 550 °CNo burning: the ash is dissolved and tested in solution
ExampleBiscuit ash 1.5 percentMilk calcium or flour iron, reported per element
Use on a labelPart of the proximate compositionThe mineral values printed on a nutrition label
LimitCannot say which minerals are presentNeeds the ash step first, and one test per element or group

Scientific explanation

Definition

Ash: the inorganic residue left after a food is burned completely in a furnace. Mineral content: the amount of one named mineral element in the food, such as calcium or iron, measured separately.

Working principle

Ash: the sample is first charred gently over a low flame so that it does not flare and spit, which would throw material out of the dish. It is then placed in a muffle furnace until the ash is white or pale grey and its weight stops changing. The organic parts, carbon, hydrogen, and nitrogen compounds, burn away as CO₂, H₂O, and N₂, and what remains is the mineral part: calcium, potassium, sodium, magnesium, iron, phosphorus, and the rest, as oxides and salts. Mineral content: the ash itself is dissolved and tested for single minerals, which is the starting point for the mineral work in Unit 6. Sodium and potassium are measured by flame photometry, and calcium, iron, zinc, and others by atomic absorption.

Apparatus

Ash: muffle furnace, dish, low flame for charring, desiccator, and balance. Mineral content: glassware for dissolving the ash, flame photometer, atomic absorption spectrometer, and standard solutions of each mineral for calibration.

Measurement procedure

Ash: weigh the sample in a dish, char it gently, burn it in the furnace near 550 °C until the ash is pale, cool it in a desiccator before weighing, and work out the percentage. Mineral content: dissolve the ash, prepare standard solutions of the mineral being tested, measure the sample against the standards, and report each element on its own.

Factors affecting readings

Ash: strong heating makes the sample flare and spit, throwing material out of the dish, and lost material means a low ash result. Volatile minerals, such as some sodium and potassium salts, can be lost at high temperature, so the stated temperature is followed exactly. Ash can reveal adulteration: flour with added chalk or sand shows a high ash, and a spice cut with brick dust shows it too. Mineral content: interference from other elements in the solution can shift the reading, which is why standard addition is used to beat interference in the FTN mineral work.

Formulas and calculations

Ash percent = weight of ash divided by sample weight, times 100. There is no single formula for mineral content: each element is worked out from its own calibration against standard solutions.

Worked example from the FTN Food Analysis notes: a biscuit sample weighs 3.000 g, and the ash left after burning weighs 0.045 g. Ash = 0.045 divided by 3.000, times 100 = 1.5 percent. If the same biscuit tested at 4.0 percent moisture, 8.0 percent protein, and 20.0 percent fat, the remaining carbohydrate by difference is about 66.5 percent, which is the kind of cross-check the ash value makes possible.

Industrial applications

  • Flour mills watch ash to judge extraction: a high ash can mean more bran or added mineral matter.
  • Spice buyers use ash to spot adulteration, such as brick dust in a spice.
  • Nutrition labels carry single mineral values, such as calcium and iron, measured from the dissolved ash.
  • Proximate analysis uses ash as a check: moisture plus ash plus protein plus fat plus carbohydrate plus fibre should add up to about 100 percent.

Advantages and limitations

Ash content: it is simple, it needs only a furnace and a balance, it gives the total mineral content, and it checks the proximate sum and can reveal added mineral matter. Its limit is that it cannot say which minerals are present or how much of each.

Mineral content: it gives the detail a label needs, element by element. Its limit is that it needs the ash step first, it needs one calibrated test per element, and it costs more time and equipment than the ash test alone.

FAQ

Question: A flour ash reads 2.5 percent when the usual value is under 1 percent. What should the analyst suspect?

Added mineral matter, such as chalk or sand, or a very high-extraction flour carrying more bran. The next step is to look at the ash and test for the minerals that would explain it.

Question: Why char the sample gently before putting it in the furnace?

Because strong heating makes the sample flare and spit, throwing material out of the dish. Lost material means a low ash result and a wrong answer.

Question: If ash gives the total mineral content, why measure single minerals at all?

Because a label must say how much calcium or iron the food holds, not only how much mineral matter in total. Only the single-mineral tests give that detail.

Question: Why must the ash dish be cooled in a desiccator before weighing?

So the ash does not pick up water from the air while it cools, just as in the moisture test. Picked-up water would make the ash read high.

References and further reading

  • FTN Food Analysis, Unit 3: Moisture and ash (notes on disk): ash near 550 °C, worked example 1.5 percent, adulteration checks.
  • FTN Food Analysis, Unit 6: Mineral and vitamin analysis (notes on disk): from ash to mineral solution, flame photometry for sodium and potassium, atomic absorption for calcium, iron, and zinc, standard addition.
  • Nielsen, S. S., Food Analysis, Springer: ash and mineral analysis (consulted through Google Books).