Login Register

Access the GIFSQ Portal

Select your user type to log in or register a new account.

Student Portal

Access your food safety courses and exams.

Instructor Portal

Manage courses, view student submissions, and grade quizzes.

Company Portal

Manage corporate setup, view employee logs, and access QA services.

Food Technology Loksewa – QC

GIFSQ ID: ART-1191

Test your knowledge with this free 20-question QC quiz from Food Quality Assurance & Quality Control — part…

What this quiz covers

This Loksewa set is about quality control, the operational half of quality management: the operational techniques and activities used to fulfil quality requirements, such as inspection and testing. The inspection questions follow a product through the plant in the three classic stages, incoming, in-process and finished-product inspection, and ask when each check is the right tool: acceptance sampling to decide a lot from a sample, with AQL, the acceptable quality level, and 100 percent inspection when one defect could cause serious harm and inspecting every unit is feasible.

The heart of the set is the control chart: the X-bar and R pair for measurable characteristics such as fill weight, the p-chart for the fraction of defective units, the three-standard-deviation control limits, and the run rules, where eight consecutive points on one side of the centre line means the process mean has shifted. The ideas that explain them: control limits reflect the natural variation of the process, specification limits reflect what the customer or regulator requires, a point beyond the limits signals a special cause, and Cp and Cpk measure how well a stable process fits the specifications. The set closes with the laboratory and the paperwork: calibrated instruments, retained samples for later disputes, nonconforming product identified and segregated, rework only when the product can be brought into specification, the Certificate of Analysis for a lot, validated methods, and environmental monitoring that checks hygiene controls.

Control limits are not specification limits: the distinction the chart questions turn on

This distinction decides most of the chart questions, so keep the two voices apart. Control limits are the voice of the process: they come from the data itself, three standard deviations either side of the centre line, and they say whether the process is behaving normally. Specification limits are the voice of the customer: they come from outside, set by the customer or the regulator, and they say whether the product is good enough. A process can be in control and still make out-of-specification product, which is what Cp and Cpk measure, and a point outside the control limits is a signal to investigate, not a verdict on the specification.

How to use this quiz

Take the quiz cold first, then read the explanations below the player. Each answer gives the reason behind the key, with the numbers and definitions a food technologist is expected to know by heart.

Food Technology Loksewa – QC
Uncategorized

Choose how you want to play

Sound effects
🔈 Volume
Show explanations
🔊 Auto-read every question
Reading speed

Note: the player shuffles the questions and the answer options on every attempt, so the numbers in the player will not match the numbers in the explanations below. Match each answer by its wording.

Answer explanations

Worked through the quiz? Here is why each correct answer is correct: the concept behind it, in plain terms.

  1. Quality control is best defined as:
    1. Only management meetings
    2. Only advertising
    3. The operational techniques and activities used to fulfil quality requirements, such as inspection and testing (correct answer)
    4. The same as quality assurance

    Correct answer: The operational techniques and activities used to fulfil quality requirements, such as inspection and testing. QC is the operational part of quality management , the techniques and activities used to fulfil quality requirements, such as inspection and testing (ISO 9000:2015).
  2. The three classic stages of QC inspection in manufacturing are:
    1. Buying, selling and advertising
    2. Design, price and promotion
    3. Hiring, training and firing
    4. Incoming, in-process and finished-product inspection (correct answer)

    Correct answer: Incoming, in-process and finished-product inspection. The classic QC inspection stages are incoming (raw materials), in-process (during manufacture) and finished-product inspection , each gate catches problems before they move downstream.
  3. AQL stands for:
    1. Average Quantity Limit
    2. Acceptable Quality Level (correct answer)
    3. Approved Quality List
    4. Annual Quality Loss

    Correct answer: Acceptable Quality Level. AQL stands for Acceptable Quality Level , the worst tolerable process average for a sampling plan, defined in ISO 2859-1, Sampling procedures for inspection by attributes.
  4. A control chart is used to:
    1. Set product prices
    2. Distinguish between common-cause and special-cause variation in a process (correct answer)
    3. Schedule staff leave
    4. Design packaging

    Correct answer: Distinguish between common-cause and special-cause variation in a process. A control chart plots process data over time against statistically derived limits, so special-cause variation (a real signal) can be distinguished from common-cause variation (normal noise) , Shewhart's original purpose.
  5. For monitoring a measurable characteristic such as fill weight, the usual pair of control charts is:
    1. X-bar and R charts (correct answer)
    2. p and np charts
    3. c and u charts
    4. Pie and bar charts

    Correct answer: X-bar and R charts. For a measurable (variables) characteristic like fill weight, the standard pair is the X-bar chart for the subgroup average and the R chart for the subgroup range (Shewhart variables charts). The p, np, c and u charts monitor attributes, not measurements.
  6. A p-chart is used to monitor:
    1. The average weight
    2. The range of measurements
    3. The number of defects per unit area
    4. The fraction of defective units (an attribute) (correct answer)

    Correct answer: The fraction of defective units (an attribute). A p-chart monitors the fraction (proportion) of defective units in a subgroup , a pass/fail attribute characteristic (Shewhart attribute charts). Subgroup averages belong on X-bar charts; defect counts per unit belong on c or u charts.
  7. Control limits on a Shewhart chart are conventionally set at:
    1. Plus or minus one standard deviation
    2. The specification limits
    3. Arbitrary values chosen by the operator
    4. Plus or minus three standard deviations from the centre line (correct answer)

    Correct answer: Plus or minus three standard deviations from the centre line. Shewhart control limits are conventionally set at the centre line plus and minus three standard deviations, covering about 99.7% of in-control variation.
  8. Control limits differ from specification limits because control limits:
    1. Reflect the natural variation of the process, while specification limits reflect customer/regulatory requirements (correct answer)
    2. Are the same thing
    3. Are set by customers
    4. Never change

    Correct answer: Reflect the natural variation of the process, while specification limits reflect customer/regulatory requirements. Control limits reflect the natural variation of the process itself (the voice of the process), while specification limits reflect what the customer or regulator requires (the voice of the customer) , they answer different questions.
  9. A point plotted beyond the control limits signals:
    1. A special cause of variation that should be investigated (correct answer)
    2. That the chart is wrong
    3. An opportunity to widen the limits
    4. Normal process behaviour

    Correct answer: A special cause of variation that should be investigated. A point plotted beyond the control limits is an out-of-control signal: a special (assignable) cause is very likely present and must be investigated.
  10. Process capability indices (Cp, Cpk) measure:
    1. The cost of inspection
    2. The speed of the line
    3. Staff productivity
    4. How well a stable process meets specification limits (correct answer)

    Correct answer: How well a stable process meets specification limits. Cp and Cpk measure how well a stable, in-control process fits within the specification limits , Cp describes the potential fit, Cpk accounts for how centred the process is (process capability analysis).
  11. Acceptance sampling is used to:
    1. Set the product price
    2. Decide whether to accept or reject a lot based on a sample (correct answer)
    3. Avoid all inspection
    4. Test every single unit

    Correct answer: Decide whether to accept or reject a lot based on a sample. Acceptance sampling inspects a sample and decides whether to accept or reject the whole lot, using plans such as those in ISO 2859-1 , it is a lot-disposition decision, not testing of every unit.
  12. 100% inspection is generally preferred over sampling when:
    1. Defects are trivial
    2. Inspection destroys the product
    3. A defect would cause serious safety consequences and inspection is feasible (correct answer)
    4. Production volume is enormous

    Correct answer: A defect would cause serious safety consequences and inspection is feasible. 100% inspection is warranted when a single defect could cause serious safety harm and inspecting every unit is practical , there, the residual risk that sampling always leaves behind is unacceptable (standard QC inspection economics).
  13. A run of eight consecutive points on one side of the centre line suggests:
    1. That the chart should be discarded
    2. Perfect process control
    3. A shift in the process mean — a special cause (correct answer)
    4. Normal random variation

    Correct answer: A shift in the process mean — a special cause. Eight consecutive points on one side of the centre line is a classic run rule indicating that the process mean has shifted , a special cause, not random scatter (Western Electric run rules).
  14. QC measuring instruments must be calibrated because:
    1. Calibration makes them faster
    2. Uncalibrated instruments are cheaper to run
    3. Uncalibrated instruments give unreliable results and wrong accept/reject decisions (correct answer)
    4. It is only ceremonial

    Correct answer: Uncalibrated instruments give unreliable results and wrong accept/reject decisions. Instruments must be calibrated because uncalibrated instruments give unreliable readings, which turn into wrong accept/reject decisions on product (ISO 10012 measurement management; ISO/IEC 17025 §6.4).
  15. Retained (reference) samples of finished product are kept to:
    1. Increase warehouse stock
    2. Decorate the laboratory
    3. Avoid testing
    4. Allow future investigation of complaints or disputes (correct answer)

    Correct answer: Allow future investigation of complaints or disputes. Retained (reference) samples of finished product are kept so that customer complaints or disputes can be investigated later against the product as it was actually shipped (GMP retention-sample practice).
  16. Nonconforming product in QC must be:
    1. Identified, segregated and dispositioned through a controlled process (correct answer)
    2. Hidden from auditors
    3. Shipped quickly
    4. Mixed with good product

    Correct answer: Identified, segregated and dispositioned through a controlled process. Nonconforming product must be identified, segregated and dispositioned through a controlled process, so it can never be used or shipped by mistake (ISO 9001:2015 §8.7, control of nonconforming outputs).
  17. Rework of a nonconforming food product is acceptable only if:
    1. The customer will not notice
    2. It is done quickly
    3. It can be brought fully into specification without compromising safety or legality (correct answer)
    4. It saves money

    Correct answer: It can be brought fully into specification without compromising safety or legality. Rework is acceptable only if the product can be brought fully into specification without compromising safety or legality , otherwise the reworked food is still nonconforming (GMP/HACCP disposition principle).
  18. A Certificate of Analysis (COA) provides:
    1. A price list
    2. Test results for a specific lot against its specifications (correct answer)
    3. A marketing guarantee
    4. An import licence

    Correct answer: Test results for a specific lot against its specifications. A Certificate of Analysis reports the test results for one specific lot against its specifications , it documents what was measured, not prices or licences.
  19. QC test methods should be:
    1. Validated or recognized standard methods suited to the purpose (correct answer)
    2. Invented on the spot
    3. Copied from competitors secretly
    4. Changed with every batch

    Correct answer: Validated or recognized standard methods suited to the purpose. QC test methods must be validated or recognized standard methods suited to the purpose, so results are reliable and defensible (ISO/IEC 17025 §7.2, selection, verification and validation of methods).
  20. Environmental monitoring in a food plant (air, surfaces) is a QC activity that:
    1. Tests raw material prices
    2. Verifies hygiene controls are working by detecting contamination trends (correct answer)
    3. Replaces cleaning
    4. Measures staff morale

    Correct answer: Verifies hygiene controls are working by detecting contamination trends. Environmental monitoring of air and surfaces verifies that hygiene controls are working by detecting contamination trends before they reach the product , it checks the controls; it does not replace cleaning (HACCP verification principle).